Good afternoon I have an Xbox 360 that to press the control wants to start turns on the fan a second and stops and at the source the orange standby light turns green a second and returns to orange. I changed the source recently I put a non-original because the one I had burned. Thank you very much in advance for your help.

GOOD NIGHT FRIEND I COMMENT THAT THE 360 HAS DIFFERENT FUNCTIONS OF LS LIGHTS TO REPORT A PROBLEM I APPENDIX MORE DETAILED INFORMATION Well ... I created this thread to put this info that is too important and I was forgotten too far back in the forum ... the first thing that should be done before any error suffered by your console is to look in this thread that error has suffered .. and in the case of the famous 3 RED LIGHTS ... learn how to get the hidden error code and how to interpret it .. to then go to your solution (rubber, coins, heat gun, change tweezers in X.etc) Xbox 360 Erorors: -------------------------------------------------- -------------------------------- -------------------------------------------------- -------------------------------- / \ \ / The specific type of hardware failure can be determined with the error displayed on the screen. If the screen is blank or you want additional information follow the instructions to determine the secondary error in the secondary errors section. E64: DVD Drive error. E65: DVD Drive Error E67: Hard Disk Error. It can be a problem with the same hard drive or with the connection of it. Try to remove it and play without it. E68: Hard Disk Error. It can be a problem with the same hard drive or with the connection of it. Try to remove it and play without it. It can also be caused by an error of the Hard Disk Eprom. E69: Hard Disk Error. It can be a problem with the same hard drive or with the connection of it. Try to remove it and play without it. E71: It is not known E73: There is a problem with the HANA video encoder chip. E74: There is a problem with the HANA video encoder chip. E76: It is not known E79: Hard Disk Error. It can be a problem with the same hard drive or with the connection of it. Try to remove it and play without it. -------------------------------------------------- --------------------------------- -------------------------------------------------- --------------------------------- Secondary error codes (hidden) The type of hardware failure can be determined by a "hidden" error code Turn on the Xbox 360 and wait for the red lights to appear. Press and hold the sync button (the little white one) while holding down the Eject button (the dvd drive button) The LEDs will now show the first code (as described below) Stop pressing the eject button and then press it again. The LEDs will now show the second code. Stop pressing the eject button and then press it again. The LEDs will now show the third code. Stop pressing the eject button and then press it again. The LEDs will now show the fourth code Stop pressing the eject button and then press it again. The LEDs will return to the initial red lights. This is how the codes are interpreted in the LEDs: The four lights on - 0 A light on - 1 Two lights on - 2 Three lights on - 3 0001 electrical problem 0002 electrical problem 0003 is not known ... 0010 overheating 0011 overheating 0012 overheating 0013 overheating ... 0020 Possible plate dilation. 0021 DVD drive time out 0022 GPU Error / GPU Overheating (Graphics Processing Unit) ... 0101 Not known 0102 False contacts Ram memories, plate dilation. This error that was previously unknown and is the most frequent is solved with the method of rubber + coins (read the terbarius tuto that is very well explained) ... 0110 Memory Error / Memory overheating. ... 1003 Hard Disk Error ... 1010 Hard Disk Error, may be caused by a missing or corrupt Eprom. ... 1013 Not known ... 1020 Not known ... 1022 AV Cable or Internal AV Encoder Problem ... 1030 Not known -------------------------------------------------- --------------------------------- -------------------------------------------------- --------------------------------- Console Reset Codes This section refers to software solutions to clean the system from wrong updates or system files. * Clear all installed game updates and memory cache. -Go to the "System" tab -Select "memory" -Press Y in the simplicity of HD or Memory -Press X, X, LB, RB, X, X -A message will appear Saying: "Do you want to carry out the maintenance of your storage devices?" -Select YES * Clean any erroneous update or system file that causes error when starting the system. -With the console turned off, press and hold the synchronization button (the white round button to synchronize the wireless controls) -While holding down the synchronization button, press the button to turn the system on. -Continue keeping the synchronization button until the console starts completely. -During the boot of the system the console should delete all the files and / or failed system updates allowing you to use the system again without any errors.

Solved was the source. I made one with an ATX and it's perfect for me. Thank you for your cooperation!