⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
Cars and trucks

corsa 2,200-1.8 gls gas-does not work speedometer.

hugoivanguzman
hace 5 años
hace 5 años
Good to the forum. I wanted to consult you for a failure in auto corsa 2, the speedometer fails. This model does not have a sensor in the box, or transmission. What it does bring are 4-wheel sensors, for the operation of the abs. I wanted to know if someone could guide me with this fault. Check the 4 sensors and measure continuity to the tab that is connected to the abs.medi module in ohm each and give me a value of approximately 1500 each. I lifted the front wheels and spun them and measured alternately. and also in hertz and if they generate said signal and reach the abs module. The rear wheels have tangential sensors. I spin them and they do not generate me alternately. I ask: they would have to generate the rear wheels, signal, bone alternating current, or how they would have to measure their signal. Would someone have the circuit or diagram of the sensors and / or where the speedometer takes a signal? I also have the fuse and relay diagram of this model, if someone could guide me or collaborate with the diagrams, from now very grateful. I wanted to note that the abs light came on like a year ago. and the speedometer stopped working a month ago, when the speedometer did not work, the car tends to stop when I brake. Thank you very much, I hope you made me understand. Thank you
BIN2013
BIN2013
2.689
hace 5 años
hace 5 años
Friend, you checked the fuses, something else can be the cable branch that controls the installation is not cut or stripped!
hugoivanguzman
hace 5 años

Hi friend, thanks for commenting. The sensor cables are not cut. you fuses ok. I need to control 5 cables that connect to the abs module. I imagine they are going to the ECU, warning light of the panel, stop switch, diagnosis tab. I would miss one. think it is so. I follow and measure the cables and comment, some guidance, grateful. greetings

Responder
charly48
charly48
1.712
hace 5 años
hace 5 años
I think that you are answering your own question, and I explain why, the speedometer receives a speed signal from the ABS management module, since as you said, there is no VSS, so if I have anomalies for a year In this module, it is reasonable that at some point and due to system degradation, I will be left unmarked in the table. In addition, this symptom is perceived by the engine ECU, reacted as in almost all systems when there is no speed signal, the ECU stops managing the idle function, acting erratically.
hugoivanguzman
hace 5 años

Hello, good morning, thanks for answering, I have some doubts on how to measure the signal in the rear sensors. Since if they measure in ohm, but I spin the wheel but they do not measure, as if they did not generate, the rear sensors are different from the front ones. Physically different. My question is whether these would have to generate an alternating signal. I can't find information about them, only that they are tangential, like to rule out that these are the ones that produce the fault. First I want to rule out that they are the rear sensors, then the cables that carry the signal to the frame and / or ECU. some other orientation. a lot of grace

Responder

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

4.25
(8)

Reparación de Placa Main TV LED con el Ing. Picerno

Ing. Alberto H. Picerno
$ 40 USD
$ 20 USD
4.6
(10)

Curso Localización de Fallas en Refrigeración en Heladeras/Neveras On/Off

Yamil Alarcón
$ 29 USD
$ 12 USD
4.64
(45)

Curso Tecnología Inverter - Fabricación de probadores y herramientas

Yamil Alarcón
$ 240 USD
$ 40 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis