Another thing the image is distorted horizontally from time to time
I do not know if it is appreciated but where it says width adj cut is missing a component that was welded and I do not know what component it is because the TV has a blow that probably took the component
Photo of the complete plate 
Plate Model: 3003-705-710
TV Model: TV-1200
Extra: IRT ALBA 12 '
Good afternoon, any of the data provided by you do not generate links to look for diagrams or any other information, except for some photographs. You have another fault, it is not related in itself to the horizontal stage, for which I think it did not need to replace a condenser that is practically not used at present, it is not commercial, if there are any they should be quite expensive, he said: replace it with a modern one, he did not mention it seems to me if the new capacitor was not polarized, for me that put an electrolytic one ...
For me you have a fault in the IF stage ... (If the fault is that of the first photos) For me it has nothing to do with the capacitor that replaced without results ... List the integrated circuits of the board, in some of those there are data sheets, I don't think, but nothing is lost with trying ...
The condenser that replaces a new one is the one that exploded but I put one exactly the same as the original one from where I got it? I took it out of a TV board just as it was split and just for me luck was that condenser so I changed it and fixed the image of going to delay lines with white image to video image.
Well changing the subject I found the diagrams of the integrated video and audio that are around the internet
Well, but you ask, he answers, but he doesn't let himself help, because he doesn't answer the questions of the colleagues properly ... Several times I insisted on mentioning the address of the capacitor, he didn't, now I asked him to mention the IC (The registration of the IC, and it does it again, does not mention anything at all) It is not for you anything else, if not to know all where we stand, we need correct coordinates and answers from you ...
These televisions can be complicated by the simple fact that you do not have solid knowledge in electronics, it is not: I see that you have at least two ICs, probably because of what I notice they also have heatsinks, surely just copper plates .. (That it would be an inconvenience when looking at their license plates, otherwise with the individualized plates correctly you can search the data sheets of each component and see what each one of them do)
I do not know if the plate endures the use of thinner, the somewhat old plates did not usually do it, because that is why I do not suggest that you use this solvent, but the plate should be cleaned, it is the right and appropriate, at least to see more Of course the panorama, you can use isopropyl alcohol, in my locality it costs an eye of a face, but hey ...
Very well, that was necessary before, when he had the assumption that those capacitors were the cause of the fault ... You know that no ... The addresses or coordinates is simply to coordinate efforts with some diagram, from your TV there is no ... But now we go through the license plates of the ICs that make up the chassis, some of them process the IF signals, some of them the geometry ... Etc (Or combinations of several stages) INSIST for me You have a fault In the FI video stage, you must locate that stage and review it ...
If you find condensers in poor condition, with loss of liquids, you must replace them without more or more, they do not necessarily have to do with failures, many times in the cases, they do not improve when you renew them, many times when you renew them later other components are affected ...
Look I found something very important, well, do you remember that in the previous post I put a condor exploded? well I understood why such a problem repaired only that now instead of exploding it is distorted horizontally, why is it distorted? Because a component of the horizontal c614 is missing Why is it missing? Because there are only the pins soldered to the plate but the component was ripped off or maybe it just burned and came out there I don't know. This missing component can reach some ends that I don't want to reach and it is not loose inside the TV because I already checked
Hey you told me that missing component is from the horizontal right? Well that component is causing me a failure that I thought was repaired in the previous post I put a condenser burning but before burning a vertical line is seen for about 1 second and then the condenser explodes I need to know which component is the one that is missing because He is responsible for that explosion.
The location of the component: c614
I already understood what happens because so many screen problems weird sounds etc. The flyback has an internal leak and from both on turn off check change the source has a problem the flyback. The horizontal repair it but the flyback now not only shows a flash on the screen because of the flyback and why does the flyback have a problem? Because it was rusty and I never gave the most importance is the 2nd TV that I can not repair by internal leakage so I will keep it until I find the replacement of this and the same with the other thank you for guiding me to the problem :)
