mello

150

hace 5 años

hello friend victor, and what should i do? Does a 55w light bulb help me?

Victor E

65.783

hace 5 años

yes, it must be incandescent not type low consumption.

Victor E

65.783

hace 5 años

You should insert the bulb between the plus and the + b input on the flyback. It is connected in the chassis of course.

mello

150

hace 5 años

I told you that I did what you told me and the flay began to scream, disconnect it from one, what should I have done or looked at my friend Victor?

Victor E

65.783

hace 5 años

The light bulb lit? short the line of + b that goes to the flyback to insert the light bulb? that is, the light bulb must bridge between + by and the flyback as shown in the image I sent.

Victor E

65.783

hace 5 años

just in case I don't check the horizontal transistor that is not short or crossed?

mello

150

hace 5 años

Yes friend Victor, I put it in series to the flayback, I will check the tsh to see

mello

150

hace 5 años

| and if the bulb turned on normal

Victor E

65.783

hace 5 años

You must have the horizontal transistor connected for that test.

mello

150

hace 5 años

I measured it and it's fine, so on a dido scale (+ b with -c 368 on the back 0) (+ b with -e 55 equal on the reverse) and between c and measured as a diode

Victor E

65.783

hace 5 años

If it's ok, can the source be the one that fails, do I check the + b filters?

mello

150

hace 5 años

I did the test with a 55w bulb, I put it in series on line + b to the flayback, I gave it a light and the flayback sounds and the bulb turns on normal ... all this with the tsh connected, then I took it out and measured it for what you told me and that's fine, I already sent you the measurements ... will it be the flay that is fried then friend victor?

Victor E

65.783

hace 5 años

If the source is good it can be the flyback, or the yoke too.

mello

150

hace 5 años

I just checked them and they measure the filters well, what's next friend Victor?

mello

150

hace 5 años

the yoke measures 4ohm and 15 ohm

Victor E

65.783

hace 5 años

Yes, but that is not a guarantee that it is okay, you can have short turns and give that measurement.

mello

150

hace 5 años

is that the funte gives me all the voltages well, I will try to find a flay and I will see it again, there I have a bsc 25n0818 will it help me?

mello

150

hace 5 años

I try it without yoke?

Victor E

65.783

hace 5 años

yes but only seconds to see if it starts.

mello

150

hace 5 años

good day friend victor, waking up with the batteries recharged to give hard to that tv, I try it without yoke aja but with or without the focus put in series to the flay?

Victor E

65.783

hace 5 años

without focus

mello

150

hace 5 años

I test it with the focus and it does the same, is that the sound is like when there is a leak, it is a shriek ... I am afraid to try it without the focus because Capaza blows my fuse and the mosfet again, will I do it?

mello

150

hace 5 años

I tried it without the spotlight and saw a spark from the flay bac's abjo part and disconnected it once

Victor E

65.783

hace 5 años

if the squeak is the flyback, is that just try to try another one

mello

150

hace 5 años

Ok I will look for another one to see what I get, I will wait a few days, but I find it I close the post with this solution friend victor do you think? I'm going to check another TV that I have I'm going to open the post to see if you help

Victor E

65.783

hace 5 años

give better response and close greetings