⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
LG

21 "slim lg TV model 21FU1RL does not turn on

winston arid genoy
hace 5 años
hace 5 años
Hello friends, it turns out that I got this LG brand TV with the power failure checking it I found that I did not have the + b from its + by filter I found the horizontal transistor c6090 open on its three pins I removed it and connected it without the transistor and obviously I had the + b to the transistor as I do not have this transistor I put a transistor d1877 with damper but the TV on turning on it sounds a swiche and the + b is lost I would appreciate your collaboration
Victor E
Victor E
65.783
hace 5 años
hace 5 años
Place a transistor without damper. Check the capacitors in the TSH collector. Measure the voltage of + b if correct. greetings
winston arid genoy
hace 5 años

I don't have that transistor but I'll go look for it in the spare parts stores

Responder
Victor E
Victor E
65.783
hace 5 años

Before placing the new check what I said.

Responder
winston arid genoy
hace 5 años

The voltage in the collector is 110v

Responder
Javier Chavez C
hace 5 años
hace 5 años
What voltage you get in + B both in STAND BY and on the ON command. What voltage do you get on the horizontal DRIVER transistor in both STAND BY and ON. If the + B voltage is within its nominal working value, remove Q16 from the circuit ..... and observe effects
winston arid genoy
hace 5 años

The voltages in + b is 110 the transistor c6090 is a transistor without damper and the d1877 has damper can be used without problem

Responder
Javier Chavez C
hace 5 años

For the test there is no problem, then you have to place one of the characteristics of the original.

Responder
nicomena2015
nicomena2015
9.501
hace 5 años
hace 5 años
hello buddy: if it's the CW81B chassis ... if when giving power it stays if + b ... test source performance ... remove the ptc from the board to avoid confusion .... remove the TSH from the plate ... connect a 60-75w filament lamp between the + by mass or between the positive of the C814 and mass ... and then see if the 110v in C814 remain stable ... in this chassis the + b is of 115v ,,, change the C814 of 220mfx160v ... if the + b remains stable check (fli-bak and C414 -417 in TSH collector) and see if there is no damaged ... check vertical stage see if no there is a short in the vertical lc ... you can remove the Q16 from the board ... but in this case the tv is left unprotected ... in this case it is convenient to connect a 200w filament lamp between the tv and the mains to avoid a possible short ... if it does not have 200w you can connect 2 of 100w in parallel ... you can connect them in the place of the fuse in the primary of the source ... in this scheme the TSH appears with damper .. .comment chassis number ... s greetings !!
winston arid genoy
hace 5 años

It turns out that I placed the d1877 transistor and turned it on but it warmed up in 30 seconds, I checked the filters but I didn't find any broken ones, these are porcelain as I can check the

Responder
nicomena2015
nicomena2015
9.501
hace 5 años

The TSH has a good decipator ... look at that ... it should have a large size decipator ... and the tsh well attached to the decipator ... if the TSH overheats so fast ... it may have some overload on the stage hor, .. when you turn on the tv it looks good on the whole screen ... it looks widened in the hor sense, ... the + b stays at 110v when giving power ... check or measure the diodes that are between the TSH manifold and ground and see if they are not leaking ... if it is the CW81B chassis the C414 and 417 must be polyester ... see if they are the originals ... mention chassis number ... try with the D1887 without damper.

Responder
winston arid genoy
hace 5 años

Hi friends thanks for your input but it turns out that I had a c414 capacitor that mediates well but at the time of working this presented a leak replace it and the TV worked perfect

Responder
nicomena2015
nicomena2015
9.501
hace 5 años

Hello colleague: I'm glad that the TV is already working ... the prob, I had it in C414 as I suggested in my first comment ... do not forget to value my contributions as a solution ... this way it remains in the solutions file for other colleagues ... "congratulations" on the achievement ... until another opportunity .... greetings!

Responder
Victor E
Victor E
65.783
hace 5 años

I told him first, "check the capacitors in the tsh collector" so the solution corresponded to me but you gave it to you only, to enjoy it.

Responder
nicomena2015
nicomena2015
9.501
hace 5 años

Hello colleague Victor ... excuse me, the colleague has given me the solution ... you are right ... it was up to you the solution ... if there is a way to change the solution there are no problems colleague ... Tell me how I have to do it ... that usually happens ... and it has happened to me too ... Anyway I leave you a like since, you deserve it not only x the wrong solution but also good x partner ... I hope you know sorry for this mistake ... regards!

Responder
Victor E
Victor E
65.783
hace 5 años

no problem, what is done is done, and has no solution. greetings

Responder

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis