screen divided into 2 vertical, compressed image
Of course, I didn't know it was a 3d screen. Be careful, because if you update the firmware and it does not correspond to the exact model it can be disabled
Hello, enter a mode factory (home + 1999 + return) and in Panel_ID the code of the original screen appeared (228) (that is, with 062598 + home + 050 I did not change it) then I put there in panel_id the code 50, and left mode factory, turn off the tv. and turning it on now the whole screen appears in green. I tried to put the code it was bringing (228) with 062598 but it restarts and remains the same, that is, it does not change it. and I can't enter mode factory because nothing is read. What can I do? Can I delete the changes I made in mode factory? If it is reset, the changes will be deleted? Thank you. regards
doing a reset should be all the parameters as they leave the factory and then it should be programmed as when it is a new TV. But with the problem that cut you and I reversed half a screen I don't know if you will see the letters to do it.
Yes, recording the memory, but you need a very expensive device and it is also quite difficult to desolder it. It should take someone who is dedicated to record them, but it is very likely that you continue with the initial problem (image divided in half and inverted one of them)
Hello, trying to solve the problem, notice that when I connect the flex on one side of the panel, the t-com starts to quickly raise the temperature in the part of the power source of the tcom (that is where it handles all the voltages, and not so much on the chip) getting to burn your fingers when touched. when I connect only the other flex, the temperature hardly increases. (from the tcom comes two flex to the panel). (When the two flexes are connected, it also raises the temperature). Could it be that the panel is incorrectly configured, or does the panel have a problem on that side? regards
The side that is heated, is the one that before changing the configuration in mode factory, showed the image well, but compressed. and the side that does not heat, showed the image upside down and blurred. now they show only green, and when the two flexes are connected, it also appears in the black center in the form of v.
Hello, at the beginning you changed a 3d 4k screen to one that is not 3d (it is only 4k).
Why did you change it? What defect did the original make before changing it? Or did you change it because it was broken? and another question: was he not in another workshop before taking it?
Hello, the original screen broke, totally splintered, and new screen was not achieved, the only one I got after a year of searching, was this used (the one that sold it showed me by video that worked), which as it uses the Same main board and had the same chassis, I played to buy. I was the only one who played it on this tv. Thank you. regards
with the original screen you could see something although bad, how to change the configuration again in factory mode or did not distinguish the osd? Because otherwise I think you have to rewrite the memory, but this is a whole issue and I don't know if it will solve the initial split screen problem.
The original screen does not see anything, it is broken. but I put it on and tried to change with 062598 + home + 228 (which is the original screen number) and it doesn't change it. It does the same. It restarts and does not change the screen settings (as always). And that is another doubt, in several videos I saw that after entering 062598 + home + nro the TV turns off and you have to wait a few seconds and turn it on. and this does not turn off, it restarts itself and is checked for a while, and then as if nothing was modified
another query, the original tv is 65pug7100 / 77. and the donor tv is 65pug6801 / 77. It occurred to me to change the main one, but the only one I get from the 6801/77 series is one of 55 inches, which is the same main board, I calculate that different software. Can you put that main board? The one that handles the size of the screen is the tcom? The main board I get is 55pug6801 / 77 and has the same chassis. Thank you. regards
I can't assure you that. You have to be sure not to get into a bigger enough expense and not be sure to fix it.
Hi, I bought a main of a 49pug6801 / 77, (I didn't get a 65pug6801 / 77 that was from the donor screen). Now the image is not compressed, but it does not look good, the image is moved, and in one half the inverted image is seen. when I disconnect the flex from the right side (which goes from the tcon to the display plate) in the middle of the screen, the half image looks almost fine. but when I do it in reverse, I mean disconnect the left and connect right, nothing is seen. that same before but compressed the image.
It seems that the screen for the main is not configured. but it does the same thing that before when I put 062598 + home + 050 it restarts (it does not turn off, nor is it in standby, as it would have to do) is how it does not accept the code. And it doesn't change.
Hi Normaleg, when you bought the screen and you said it showed you by video that it worked fine, how was that, did you connect the screen to a TV? I don't think I would take apart a tv that worked well to sell you the screen, I see it weird to this.
Hello, I also have that doubt, but the seller assures me that I tried it (I don't know how he could do it either), and since it is a business that has been engaged in scrap and sale of parts a long time ago, and has a lot of experience, no I have another option to believe them. But also, the last main board I bought (49pug6801 / 77) came with all the TV, and this one has broken the screen but it looks good in 1/4 that is healthy. and there I tried the two plates (65pug7100 / 77, and the 49pug6801 / 77) and with the 7100 series it does the same thing on the other screen (it looks green).
none of the 2 plates accept me on 062598 + home + xxx, it restarts there is no standby. And it doesn't change anything. What if you notice now the 7100 series board (after changing factory mode) no longer recognizes the remote control of your series, and if the 6800 series. Thank you very much. regards
Translating the chassis manual, I think the problem is here.
Display Option Code Selection
When after an SSB or display exchange, the display option
code is not set properly, it will result in a TV with “no display”.
Therefore, it is required to set this display option code after
such a repair.
To do so, press the following key sequence on a standard RC
transmitter: “062598” directly followed by MENU and “xxx”,
where “xxx” is a 3 digit decimal value of the panel type: see
“Display Code” column in back to div.table 6-3. When the value
is accepted and stored in NVM, the set will switch
to Stand-by,
to indicate that the process has been completed.
During this algorithm, the NVM-content must be filtered,
because several items in the NVM are TV-related and not SSB
related (eg Model and Prod. S / N). Therefore, “Model”
and “Prod. Y / N ”data is changed into“ See Type Plate ”. In case
a call center or consumer reads “See Type Plate” in CSM
mode. In the last part, translated serious
"When the value
is accepted and stored in NVM, the set will change to Stand-by,
to indicate that the process has been completed.
During this algorithm, NVM content must be filtered,
because several elements in the NVM are related to TV and not with SSB
related (for example, Model and Prod. S / N). Therefore, "Model"
and “Prod. The S / N data ”is changed to“ See type plate ”. In case
a call center or consumer reads "See type plate" in CSM
mode. "But the odd thing is that it also does not accept the value it brought before.
Elsewhere it says "SSB ID
The SSBs of this chassis are identified by a code "715" in the SSB.
715Axxxx-Nnn-MMM-OOOO
• 715 main category, printed wiring board
• Subcategory Axxxx, sequential coding number
• Nnn version code
• N development number
• nn production number
• MMM assembly variation code
• Optional variation code OOOO
Make sure that when replacing an SSB the SSB identification codes
coincides with the replacement panel "But it is impossible for me to know the identification code if SSb had the donor screen,
Did you do the translation with a computer program? because I don't see her very correct. Anyway this escapes my possibilities; I think you should consult a Philips help center or open a new post by placing all the data and see if someone can advise you.
If the 3-digit code does not appear when you enter the service mode, try this:
062598 menu and then place the 3-digit code of the new screen. then continue as in the previous case.
Hello, thank you very much for responding, with 062598 + menu you do nothing, but with 062598 + home (the button with the house) I receive code, it goes out, but it remains the same. the screen that brought the TV has code 228, and the donor tv screen has code 50, probe putting 50 and 050, but all the same. Thank you. regards