LG TV 32LG30R LCD C hassis LP81A.
It does not turn on only red standby light flashes a few seconds and is paid. And pressing the power button, the second you see a very short flash, as if they were going to turn on the lamps, and the red LED light is paid. The power supply card is backed up. All the capacitors were tested and they are fine. Power Source: Connector that goes to the main card. PWM Dim = 126 mVolts INV = 3.18 non-stable goes down to zero and goes back up to 3.18.ON / OFF 3,048 Volts ACD 4.31 Volts 5.2 Volts there is 5.11 Volts. 2 Volts there is 12.4 volts 16.6 volts there is 15.70 volts Second connector that goes to the inverter card.Erro 0 or voltsPW Dim = 3.2 voltsINV 23.3 mv24 volts there are 24 volts Main card: Sub sources: Regulator output 5 volts, 1.8 volts, 2.5 volts, 1.2 volts and 3.3 volts of the latter are present there are two regulators With the same voltage. All according to what the plate indicates. I request help with this fault.
⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta.
🔥 Aprovechar oferta ahora 🔥
LCD TVs - LED
LG TV 32LG30R LCD C hassis LP81A.
It does not turn on only red standby light flashes a few seconds and is paid. And pressing the power button, the second you see a very short flash, as if they were going to turn on the lamps, and the red LED light is paid. The power supply card is backed up. All the capacitors were tested and they are fine. Power Source: Connector that goes to the main card. PWM Dim = 126 mVolts INV = 3.18 non-stable goes down to zero and goes back up to 3.18.ON / OFF 3,048 Volts ACD 4.31 Volts 5.2 Volts there is 5.11 Volts. 2 Volts there is 12.4 volts 16.6 volts there is 15.70 volts Second connector that goes to the inverter card.Erro 0 or voltsPW Dim = 3.2 voltsINV 23.3 mv24 volts there are 24 volts Main card: Sub sources: Regulator output 5 volts, 1.8 volts, 2.5 volts, 1.2 volts and 3.3 volts of the latter are present there are two regulators With the same voltage. All according to what the plate indicates. I request help with this fault.
LG TV 32LG30R Does not turn on only red standby light flashes a few se
184
hace 5 años
hace 5 años
LG TV 32LG30R LCD C hassis LP81A.
It does not turn on only red standby light flashes a few seconds and is paid. And pressing the power button, the second you see a very short flash, as if they were going to turn on the lamps, and the red LED light is paid. The power supply card is backed up. All the capacitors were tested and they are fine. Power Source: Connector that goes to the main card. PWM Dim = 126 mVolts INV = 3.18 non-stable goes down to zero and goes back up to 3.18.ON / OFF 3,048 Volts ACD 4.31 Volts 5.2 Volts there is 5.11 Volts. 2 Volts there is 12.4 volts 16.6 volts there is 15.70 volts Second connector that goes to the inverter card.Erro 0 or voltsPW Dim = 3.2 voltsINV 23.3 mv24 volts there are 24 volts Main card: Sub sources: Regulator output 5 volts, 1.8 volts, 2.5 volts, 1.2 volts and 3.3 volts of the latter are present there are two regulators With the same voltage. All according to what the plate indicates. I request help with this fault.
184
hace 5 años
Thanks Denis, you know of some simple method to try them. I live in Venezuela and everything is incomparable. Even an electrolytic capacitor are super expensive.
184
hace 5 años
Today I connected the TV to the power, and I could see that the screen turned on well for a few seconds, and turned off again (it was protected). I haven't played the TV since yesterday. For the illumination of the screen I discard the CCFL lamps.
184
hace 5 años
I already managed to turn on the TV, but if it has eprom memory failure, the volume to the maximum, lets press a key and locks. It does not work even with the remote control. Remove the control panel, check each of the buttons, and they are fine, check the associated resistors and they are fine, solve each button.
hace 5 años
hace 5 años
Hi friend, good morning. I have the same TV with the same or similar fault. I turn it on for a second how to try to give an image and the screen collapses. It does not give sound, because of the screws it is seen that the LED strips are giving brightness.
hace 5 años
hace 5 años
good night my friend, I have a 32lg30r TV that shows symbols, numbers and letters fail. There are moments that hang or turn off. I saw a tutorial apparently it is memory, someone knows how to replace it or reprogram it or a Garcia solution
184
hace 5 años
hace 5 años
The final problem was detected, because when you turn on the TV, the keyboard after a few seconds is locked, and you cannot use the remote control. The fault is the eeprom 24lc64 memory, it was tested with 24lc02, 24lc08 and 24lc16 memories, and the TV turns on starts with the auto-installation menu, the options can be selected, but when you start looking for the channels the screen goes black. The problem I am in Venezuela and I don't get that new eeprom.
¡Aprende a reparar con estos cursos YoReparo!
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis
Ad