Wireless detector dsc ws4904p.
Detector DSC WS4904P
Detector DSC WS4904P
Thanks for your answer.
I have done the test and the correct green icon turns on, but they still do not work when I set the alarm.
I have done the programming with each detector as follows from zone 1 to 6.
For example for the zone 2 detector:
* 8 5555 804 02 (ESN Detector) #
Section 001 03 (Instant) #
Section 102 (Option 8 ON, via radio) #
Section 202 (Option 1 on ON, zone attribute) #
Thus I have programmed each detector in your area.
Since the detectors are almost 12 years old, won't it be that they are dead?
Thank you.
I have a doubt when you explain how the programs, you put
* 8 5555 804 02 (ESN Detector) #
Section 001 03 (Instant) #
Section 102 (Option 8 ON, via radio) #
Section 202 (Option 1 on ON, zone attribute) #
I calculate that it will be by way of example but programs zone 2 wireless, in section 001 you put zone 1 instantaneously, 102 zone 2 wireless and enable zone 1 in partition 1, let me know if my comment was understood because it was all together, what I try to say that there are 2 different zones there and you are configuring half of each one
Thanks Andrés for your reply.
The example I have set is for zone 2 in particular.
I do the same thing wrong:
I put section 001 03 (instant).
And this means that it is for zone 1 ????
If I want to put for zone 2 would it be section 002 03 (instant) ?????
I would go little by little, memorize only 1 detector and you are testing.
In 001 the pull zones are programmed, that is if you want to program 1 beams: 001 03 ##, if you want to put 3 it would be: 001 03 03 03 ##.
Important: every time you modify something in field 001 the wireless attribute is deleted, so always check the last thing in 101, 102 ... etc, you have 8 on.
Exactly as I tell you, the error is in the configuration in section 001 you are programming only zone 1 as a snapshot, important after programming all the zones in section 001 enable the wireless zone in 101, 102, thus the 6 zones that use
The same as I said in section 202, from led 1 to led 8 each mean an area from 1 to 8 to enable it must be on
Thanks for your answers.
I have rescheduled them with your comments and it seems that they work better, the alarm does not always go off when I step forward but it seems to work better.
And if I want to put the zone 5 of the 6 that I have present / absent, it would be like this:
Section 001 03 03 03 03 32 03.
The 32 comes in the programming template in zone definition (present / absent snapshot).
It is to activate the alarm when I am indoors.
Thanks everyone for your help.
I think the programming is already done well, even though the detectors fail a lot and the alarm does not always go off.
I will buy some new and try.
Keep in mind that wireless sensors have a standby time to save batteries. I mean, they see you once and then for a few minutes they don't see you again. It's between 3 and 4 minutes if I remember correctly. Keep that in mind ! It can also happen that after the test time of the sensor, the light does not come on which does not mean that it does not see you, that also happens.
Try to turn on the alarm, leave, allow 5 or 6 minutes and enter again by going through each sensor and then check.
If I do that.
I set the alarm and go to work, when I come I can be inside the house for an hour without the alarm going off.
In the end it jumps but it takes a long time until they detect something, sometimes it does not jump ...
Any suggestions to buy the detectors?
On eBay I have seen them but it goes on outside, in Spain I can't find them.
Thanks for your comment.
Greetings
Reparaciones similares solucionadas
¡Aprende a reparar con estos cursos YoReparo!
