⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
Refrigerators

general plus air conditioning

ALBENI
ALBENI
14
hace 6 años
hace 6 años
the console turns on normally, but after about 30 minutes it marks E04, then it goes off, which means that error,
Fermin 007
Fermin 007
57.307
hace 6 años
hace 6 años
Check the area of the condensing unit, which is free of dust, that works well the fan and its capacitor, also the compressor capacitor, also checks the 2 sensors, the environmental and the pipe that are not out of range any of the 2, or failing that are 2, I do not know if in that half hour work normal, if so, it would be what I mentioned, any of these possible, luck and greetings
ALBENI
ALBENI
14
hace 6 años

thanks brother, greetings, in that half hour it works well, the sensors send them to test and they are good according to the technician who tested them, the capacitor of the compressor was changed, and the condensing unit is free of dust, which has not been checked is the condenser of the condenser unit fan, that is located on the plate ??

Responder
Fermin 007
Fermin 007
57.307
hace 6 años

must be in the same fan, greetings

Responder
Fermin 007
Fermin 007
57.307
hace 6 años

review them again the 2 sensors, personally, never trust third parties, I changed them, they should measure at 5kms at 25 ° c, if you see that they are out of range, do not hesitate to change the one that measures you wrong, luck.

Responder
ALBENI
ALBENI
14
hace 6 años

uuummmm, ok, but this causes the console to turn off?

Responder
Fermin 007
Fermin 007
57.307
hace 6 años

Ah, it changes a lot the panorama of your friend query, you never specified that the console was turned off, I thought the equipment (compressor and fans), then it is card failure or false contacts or cold wires or solders, etc etc,

Responder
ALBENI
ALBENI
14
hace 6 años

if on one occasion remove the sensors and clean contacts and resolved, but now marks the error and after 2 or 3 minutes it turns off, I have to reset what I should do, remove the card and clean completely, also check cold welding ??

Responder
Fermin 007
Fermin 007
57.307
hace 6 años

So is ALBENI friend, use a magnifying glass to check the welds and rectify those that look bad, also check the filters, these even look good physically devalue, mainly from the source, they are very complicated details, they seem easy but they are the most difficult to remove, there was once I came a similar to yours and was a cut track, until I carve I met her hehe, I cost but stay, luck and many greetings

Responder

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

4.84
(25)

Curso Práctico de Reparación y Bobinado de Motores Eléctricos

Héctor Castiñeira
$ 60 USD
$ 20 USD
4.71
(7)

Curso TV OLED y QLED con el Ing. Picerno

Ing. Alberto H. Picerno
$ 29 USD
$ 10 USD
4.64
(11)

Curso Electrónica para Reparación de Placas

Santiago Cediel
$ 29 USD
$ 11 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis