⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta.
🔥 Aprovechar oferta ahora 🔥
Air conditioner
Install universal air plate CONQUEROR ONC12RC-E
9
hace 5 años
hace 5 años
Hi. I need to change my window air plate.
It is an ONC12RC-E CONQUEROR, compact window.
The thing is that it has a dual capacitor and I'm not sure how to connect the fan and compressor to the universal board. Can I make the jumpers that I describe in the photographs to connect the fan and the compressor to the board? or yes or if I should buy the individual capacitors and from there connect them and take them to the new board?
Of course, thanks.-
11.849
hace 5 años
hace 5 años
Hello SEBAITU, in the images, it is appreciated that you have not yet removed the yellow and blue cable from the other electronic board, these are also connected to the larger relay on the universal board, if you already made the change and do not turn on the front panel or display, invert the yellow and blue wires in the relay itself that feeds the compressor from the electronic board. Comment if you still have doubts. Luck S.@lu2 friovega63.
11.849
hace 5 años
Hello SEBAITU, I will upload an edited image, to my proposal of solutions, with the connection of its electrical diagram coupled to the universal electronic board, I do not know, whether or not the speeds coincide with each color, because the universal board, does indicate that speed , corresponds to each relay, but the original CONQUEROR diagram, does not detail the speeds by color, bone that is not known if the red wire for example, really corresponds to the lowest fan speed, the blue with the average and the black wire with the highest. Change them if necessary. S @ lu2.
11.849
hace 5 años
The relay of the universal plate that indicates with the lines in red and blue, are not connected to anything, your team only has a common fan, so you do not need the Out Fan relay and it does not have a 4-way reversing valve because it is only to condition cold air, so you don't need the VR relay, which is connected to a repeat inverter valve, which is needed in other cold / heat models. S @ lu2.
9
hace 5 años
Hello! First of all thanks for your explanation.
I tell you to connect everything as you indicate and can not start. Although it is noted that it makes a kind of effort to start every few minutes (noise of wanting to start) after a few seconds it is cut off and the compressor never starts. Idea what can it be? Thank you
11.849
hace 5 años
Directly check the compressor, it could have some false contact in the input wires in its terminals, or broken cable. 2- (the fan should work, or not ?, because in that case the fan should also be checked by measuring that all its cables have communication between all, use the multimeter on the scale of 2 kilo ohm. 3- (check the capacitors with a capacimeter, as this could be damaged 4- (otherwise I should rethink a review for damage to the universal board. Comment if you doubt how to do the checks and I tell you. S @ lu2
hace 5 años
hace 5 años
Hello good day friend ...... I what you said, is what I would do .... and not what I should do. First of all I remove the plate and capacitor from the original equipment and start from scratch ... and from the cables, to connect the universal plate ..... first placed a two-leg capacitor to the motor compressor and then another capacitor to the forcer. .. the two new ones and removed the invited capacitor ...... what I see is that you are connecting the power supply of the motor compressor to the old board and not to the relay of the universal board ......... .... try to do what I say, start from scratch and it will work perfectly .... eye .... it is my humble opinion ..... best regards
Reparaciones similares solucionadas
¡Aprende a reparar con estos cursos YoReparo!
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis
Ad