Kenwood TK-805D Operation Controls: • I/O - On/Off Switch • - Monitor Mode (Squelch open) • AUX - Auxiliary Mode • REC - • SCAN - Scan Mode • D/A - Delete / Add • Volume - Volume Control • - Selects Channel Display: • CH x - Channel x selected • TA x - Channel x in Turn-Around mode (Simplex) • SCAN - In active scan mode • SC x - In scan mode, but stopped on channel x • AUX - This channel has AUX (Simplex) mode enabled • ADD - This channel is in scanning table Kenwood TK-805D Setup To enter setup mode: 1. Turn radio on while holding AUX and SCAN 2. Unit will beep 3 times. 3. Use PTT to save selection. Function Display Selections Band Range 450.000 150/250/350/450 MHz Time Out Timer t Off Off, 30, 60, 90, 120, 180 Seconds Busy Channel Lockout b On On - Enabled Off - Disabled Del/Add Condition dA On On - User selectable Off - Fixed Mic Hook Operation H On On - Scan on hook, PTT off hook, Monitor off Hook Off - Scan disabled, PTT on or Off Hook, No off Hook Monitor Priority Channel P Fl Fl - Fixed Priority US - User Selectable Monitor Switch En On On - Press to disable decode, hold to disable squelch Off - Press to disable squelch Off-Hook Monitor dE Off On - No Off Hook Monitor Off - Monitor Off Hook * Off-Hook Scan SC On On - Off Hook Scan Off - Scan On-Hook Only * Off Hook Monitor (dE Off) is only enabled when On-Hook Scan (SC Off) is Selected. When you reach END, you can power the radio off. Kenwood TK-805D Channel Programming Note: While in the programming mode, switches have these functions: • - Hold to step forward and backward thru programming (Use to move). • AUX - Hold for 1MHz step rate. • REC - Turns AUX indicator On/Off (Auxiliary mode enabled/disabled). • SCAN - Toggles between 10 KHz and 12.5 KHz frequency steps. • D/A - Turns ADD indicator On/Off (In/Out of scanning table). • - Change Selection To enter programming mode: 1. Press turn radio on while holding AUX and D/A 2. Unit will beep 4 times. 3. Use PTT to save selection. Function Options RX Frequency 390.000 to 490.000 MHz (Hold AUX for 1 MHz steps) RX Tone type Soff - No tone S dt - Digital PL S t - PL Tone RX PL frequency 67.0 to 250.3 Hz (Digital: 000 - 777, SCAN inverts) (Hold REC for 10 Hz steps, Hold AUX for 1 Hz steps) TX Frequency 390.000 to 490.000 MHz (Hold AUX for 1 MHz steps) TX Tone type Soff - No tone S dt - Digital PL S t - PL Tone TX PL frequency 667.0 to 250.3 Hz (Digital: 000 - 777, SCAN inverts) (Hold REC for 10 Hz steps, Hold AUX for 1 Hz steps) Repeat above steps for all channels. The channel number is shown in the lower right corner. Note: A display of -.--- Indicates the channel is not programmed. When channel 16 has been programmed, continue with settings below: Kenwood TK-805D Channel Programming Function Display Selections Aux selection tA tA - Talk-Around (Simplex) DRS - Digital Recording System 2tonE - 2 Tone sequential decode dt - DTMF Decode Scan Resume RX rA 3.0 1.0 to 8.0 Seconds Scan Resume TX rb 3.0 1.0 to 8.0 Seconds Fixed Priority Channel P - P - No priority Channel P xx - Channel xx is priority channel Lookback A La 1.0 1.0 to 8.0 Seconds Loopback B Lb 1.0 1.0 to 8.0 Seconds Revert Channel* CA cH sT - Selected Channel (Last channel selected before SCAN pressed) P - Priority Channel CA - Last RX channel used US - Last TX channel used * Revert channel is the channel the transmitter will switch to automatically, when PTT is pressed during off-hook scan. When you reach END, you can power the radio off. Note: The only way to clear a channel is to clear memory. Clear Memory Power radio on while holding AUX + SCAN + D/A Espero ke te sirva,cualkier cosa a mi correo paramediko@gmail.com