⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
Sanitary

Installation of water drop from the tank

pablop2000
hace 6 años
hace 6 años
Good, I am doing the new installation of hot and cold water with hot melt pipes, my doubt is about how it would be the best way to make the respective descents from the tank to the environments that will use water, it is fine to make an independent cold water drop in 25mm for each environment (4) + a 32mm drop that I then understand enters the thermos in 25mm (3/4)? after the thermos entered each room with hot with 25mm? Also attached for doubts an image of the arrangement, the tank would be up at a certain height above these environments, the thermos is inside the laundry, in each environment would be connected. of hot and cold water and in the laundry room an extra connection of cold water for the washing machine ..
danny_rosariorc
hace 6 años
hace 6 años
Okay, take 25 mm everywhere and reduce on each connection to 1/2 "that way you will have good flow. Remember that it always feeds from the bottom up to have no air. And warm on the cold, to not condense.
pablop2000
hace 6 años

Very good the "tips" of feeding from the bottom up and the hot on cold, ignore that and now that it would be putting it is great to know! Thank you!!

Responder
Ricardo Ab.
Ricardo Ab.
5.181
hace 6 años
hace 6 años
Hello Remember that the water flow is given by the diameter of the pipe and the pressure is only the height of the tank. Between 2 and 3 m from the base of the tank at the highest outlet (shower), take advantage of the outlet diameter of the tank (usually 1 "1/2) make a collector of the same size and from there distribute everywhere If you do not want to have the problem of low flow when you are taking a bath (recurring theme) would do all the descents of an inch and reduction to 3/4 in hot water tank and 1/2 in the different accessories. You can place general keys for each pipe or place 1/2 wrenches in each accessory. That way you don't have to cut off the entire supply to repair a "little rope" Regards
pablop2000
hace 6 años

Ricardo, for the doubts to see if I understood well ... the tank collector would lower in my case (according to the plan of my house) ... 5 pipes of 1 "(32 mm in hot melt I think) of which 4 pipes of those would go to the entrance of each amb (cold water) and 1 pipe that would go to the thermos, would it be like that?

Responder
Ricardo Ab.
Ricardo Ab.
5.181
hace 6 años

Hi Pablo, you understood well, it's a tip ... you can do it with 1 "or 3/4. With 1" you ensure a very good flow at all exits and forget about the shower problem. You spend a little more, it is true (it comes cheaper than a pressurizing pump) but at the time of bathing you will remember. You don't have to worry that the washing machine is working, that they use the bathroom or any kitchen faucet. The important thing is that they are independent descents, the pressure and the flow of each line will only depend on the tank. Regards

Responder
Reparaciones similares solucionadas

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

4.84
(25)

Curso Práctico de Reparación y Bobinado de Motores Eléctricos

Héctor Castiñeira
$ 60 USD
$ 20 USD
4.6
(10)

Curso Localización de Fallas en Refrigeración en Heladeras/Neveras On/Off

Yamil Alarcón
$ 29 USD
$ 12 USD
4.64
(45)

Curso Tecnología Inverter - Fabricación de probadores y herramientas

Yamil Alarcón
$ 240 USD
$ 40 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis