⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥

Excellent 8.12 Blue G

Excellent Blue 8.12 p when rinsing does not stop loading water

Jasxxx

hace 5 años

Hello people, it is an Excellent Blue 8.12 p I put it in point 1 and everything works normally until you reach the rinse load the water begins to work but does not cut the water inlet, continues to load, I have cut the power and stop, I thought to change the electrovalvula they say? Thank you

Comentar

juan guillermo caceres

23.662

hace 5 años

Hello, it may be problems of the solenoid valve, that your waterproof system is defective or it would be a matter of electronic board that the triac that governs this solenoid valve is troubled. Regards

Comentar

Jasxxx

hace 5 años

Thank you for the answer, and excuse my ignorance referred to in a tight system? Thank you



Responder

juan guillermo caceres

23.662

hace 5 años

I refer to the hermetic system of the solenoid valve, sometimes the tartar and sediments carried by the water network damage the internal menbrana that can no longer fulfill its function and is "open" indefinitely. Regards



Responder

Jasxxx

hace 5 años

Thank you, are the solenoid valves generic? because I have another washing machine and I wanted to try changing it to see what happens



Responder

juan guillermo caceres

23.662

hace 5 años

If the tab insert is the same, you can perfectly exchange them and prove what results you get. Regards



Responder

favallpa

2.523

hace 5 años

If you only do it in the rinse, I think it's a programming problem. since if in the other programs it works well, there is no problem either in solenoid valves or in triac.

Comentar

Jasxxx

hace 5 años

Thanks for the answer, when it reaches the point of rinsing load the water starts to work but does not cut the water inlet, I have touched the solenoid valves and only one feels hot, I don't know if that is normal?
If it is a programming problem, what steps should I follow? Thank you



Responder

favallpa

2.523

hace 5 años

https://www.yoreparo.com/electrodomesticos/lavadoras/drean/preguntas/1450373/codigos-programacion-placas-tipo-drean-blue



Responder



luis38

95.432

hace 5 años



hace 5 años

Dear, to confirm the origin of the problem, check if the solenoid valve that is allowing the passage of water is energized or not, (220VAC). If you have tension, you might suspect plaque. If it has no tension and allows the passage of water, the valve is defective. The strange thing is that it does not give the overload error when exceeding the water level. It would be interesting to know what happens if you let him follow the cycle. It could be that since it is a complete washing cycle, this is part of it, as is the case with other brands that start working, but continue to load water for a few moments. Regards

Comentar

favallpa

2.523

hace 5 años

I may not understand the question of JASXXXX but if the whole program works normally and only fails in the rinse, I don't think it's a solenoid valve problem .......?



Responder

Jasxxx

hace 5 años

Hi Luis, thanks for answering, change the solenoid valve, put the program on 14 (rinse) and continued loading even after starting work, it did it at a level exceeding about 5 cm the lower level of the door (no load, no clothes ) Cycle normally.
Now I'm going to try it with load
One thing I noticed in the solenoid valve that I pulled out, is that a mouthpiece (the one in the rinse, I think) had a color pulling light ocher.
I hope everything goes well, thank you all for the help, thanks



Responder

luis38

95.432

hace 5 años

Dear, it can be a normal part of the program. If it were abnormal, the washing machine would stop the cycle and give you an error message. Regarding the color of the solenoid valve is normal. The current ones differ in color to the oldest ones. Regards



Responder