⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥

Concept 5.05

drean 505 spin problems

ciprestre

hace 6 años

I have a problem with the 5.05 drean they brought it to me because I had the dead plate. well I checked it and changed the plate I put an rp plate that had input problems, I returned it and bought another one MC and when I put it on and on, turn the motor in one direction, when entering centrifuge, perform all the necessary movements with pump , actuator, and block, but when giving the order to the motor it buzzes and does not turn or is not centrifuged. you can fit the pump, change the actuator, and the block. THE MOTOR IS ALSO CONTROLLED, IT IS CONNECTED WITH BLOCK AND PUMP ACTUATOR, AND STARTING WELL. I TALK TO THE COIL AND TELL ME THAT IT IS THE PLATE, I TALK TO THE ELECTRONIC AND HE TELLS ME THAT IT IS THE MOTOR. GOOD, I'M LOOKING FOR SOMEONE WHO HAD A SIMILAR PROBLEM AND HELP ME. Apparently the problem is common. FROM THANK YOU THANK YOU AND I HOPE HELP.

Comentar

ciprestre

hace 6 años

AH I FORGOT, WHEN THE WASHER COMES INTO CENTRIFUGED FUNCTION AND BEGINS TO ZUMBAR, I DO IT ROTATE WITH THE HAND AND BEGIN TO ROTATE OR CENTRIFUGES. HE DOES NOT START ONLY, I HELP HIM AND THERE IS. That's why I thought it was the engine. THAT'S WHY I PROVIDE IT ONLY WITH AN INSTALLATION OUTSIDE THE PLATE AND I WAS PERFECTLY. OR EITHER WHEN I CONNECT WITH PLATE DOES NOT START ONLY THE CENTRIFUGATE.



Responder

sys32s

341

hace 6 años

YOU MAY HAVE PROBLEMS ON THE ENGINE .. OR IN THE LAYER .. That's why it turns in a way ... and the other is that you measure the voltage that reaches the motor .. maybe the plate sends less .. I would try .. with another layer .. With another engine .. if he does the same thing is the plate ... Never buy trout. If you are not sure that all lava components and peripherals are ok

Comentar

ciprestre

hace 6 años

HELLO THANKS, LOOK AT THE ENGINE I TESTED IT DIRECTLY WITH PUMP AND TERMOACT, AND IT WORKED PERFECT, THAT'S WHY I INCLUDED OTHERS. DON'T PROVIDE THE V THAT HAS PUT ME THE PLATE. I'LL SEE . THANK YOU



Responder

sys32s

341

hace 6 años

PLATE ... IT IS PROBABLE THAT THE TRIAC IS COMMANDING LESS VOLTAGE ...
I test the engines directly by giving positive to the layer ..
I put water ... and do what the platelet does manually ..
You put positive on one side of the layer and the motor turns on one side ..
You put positive on the other side of the layer to change the turn ..
Yes, that's OK...
The plate is failing



Responder

alturasbal

27.174

hace 6 años

Hello, if the motor works when connected directly check the wiring and connectors, if they are well the problem is board, the alternative boards give more problems than solutions, greetings.

Comentar

ciprestre

hace 6 años

WELL THANKS , . I WILL TRY TO REdo THE CIRCUIT OF THAT SECTOR AND SEE THANK YOU.



Responder

luis38

95.432

hace 6 años

Dear, I think the problem is on the side of the engine or bearings. Try it without a leash and comment it happens. Regards

Comentar

ciprestre

hace 6 años

HELLO THANKS, PROVES IT WITHOUT BELTS AND WITH PLATE AND DOES THE SAME, A BUZZER AND THE ENGINE DOES NOT START, I GIVE HIM WITH HAND AND THEN IF IT STARTS FOR BOTH SENSES. THAT'S WHY YOU THINK ABOUT MOTOR, BUT BY CONNECTING IT DIRECTLY, I START WELL WITHOUT PROBLEMS,. THANK YOU



Responder

gallorojocapacitor

40.985

hace 6 años

I change the motor capacitor ???????

Comentar



ciprestre

hace 6 años



hace 6 años

HELLO HOW ARE YOU GOING? . I WANT TO COMMENT TO YOU THAT I EFFECTIVELY FIND THE SOLUTION OF MY PROBLEM. NEITHER THE MOTOR OR THE PLATE WAS BAD, THEY WORKED VERY WELL. I DECIDED TO MAKE THE CIRCUIT AGAIN WITH THE DIAGRAM THAT I FOUND IN THE FORUM, AND FOLLOWING CABLES I FOUND THAT PIN 12 THAT SHOULD BE OUT OF CONNECTION WAS A LINE TO THE BLOCK. THEN IT CONTINUES TO MAKE THE CIRCUIT THE SAME, COMPLETE IT AND ANDUBO EVERYTHING WELL. THIS WASHER WAS IN ANOTHER WORKSHOP AND THE OWNER, TIRED OF WAITING TO BE REPAIRED, REMOVED IT AND BRING IT TO ME. SO I CONCLUDED THAT OR THERE WAS A BLACK HAND OR THE MR WHO HAD IT MISSED. FROM THANK YOU ALREADY THANKS TO FORUM TECHNIQUES AND UNDERSTANDING THAT I DID NOT FIND A SOLUTION TO MY PROBLEM. EVIDENTLY I HAD TO HAVE LOOKED MORE. OR I DO NOT KNOW . EQUAL THANKS,.

Comentar

alturasbal

27.174

hace 6 años

In my answer I suggested you check wiring and connectors, read again, regards.



Responder

sys32s

341

hace 6 años

VERY RARE HUMMMMMM ..
AS YOU TESTED THE ENGINE FROM THE SAME CABLES
.
Checking cables is like very, very wide ..
They may be talking to you even about the house wiring ..
In the future you know .. that you can test engine from the plate's tab ..
And you save a lot of headaches ..



Responder

sys32s

341

hace 6 años

Grab the card ... and from there you are giving positive to each connector ... of each peripheral ..
Check with the tester the values of the same before and avoid explosions by short ..



Responder