⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
Concept 5.05

Drean concept plate problem

Pancho7987
hace 6 años
hace 6 años
2019081916311700.jpg[563.08kb]Good afternoon, i'm having problems to measure and find equivalentss of a triac that goes in a Drean concept, the motor has to triac that are BT139BI don't have of this type of triac with 2 legs connected, i changed several of 3 legsIf you can give me information it would be useful since i don't know how to measure them to know which one's wrong and change itAnd if i need one of this type since i don't have oneI know one or both are damaged because when i plug it the engine is runningSymptom that indicates that is shortedI hope you can help meI send a picture of the triacThanks a lot
ROBERTO BERENYI
hace 6 años
hace 6 años
Triac of thre legs, the one with two doesn't exist. The one in the middle passes underneath and is connected in the weld above. Put one of the oldest plates.
sys32s
sys32s
341
hace 6 años
hace 6 años
It's of the ALTERNATIVE plates..If you have an ORIGINAL one IT'S GOING TO BE A THOUSAND TIMES BETTER..
resistencio_el_original
hace 6 años
hace 6 años
For starters, the triacs are semiconductors of THREE LEGS... in the picture i can see there's TWO welded legs and ONE that's in the middle and is shorter, that one counts too... is precisely that short leg thaat corresponds to the TERMINAL No. 2 and connects to the body of the TRIAC and finally leans and welds on the plate... In summary, as in the picture, from left to right, the first welded terminal (in the left) is TERMINAL No. 1., the second in the middle (the short leg) is the termianl that joins the body of the triac below and is the TERMINAL N. 2 and finally the right leg that's welded is the FIRING GATE.... If you suspect a short circuit, it's probable that it is present in the TERMINAL No. 1 and 2, so measuring in those 2 terminals you could measure a low resistance... Though the SLUICE GATE might as well be in short with some of them... What i'm thinking that you could do is: desolder ONE of the TRIACS and plug the washing machine and verify if the problem remains or not...if it's solved, it means that you took off the TRIAC in short, if it continues, then take off the other one and verify again... one of the 2 should cause the problem (there's a 50% 50% chacne)... All of this, assuming that those TRIACS do different things, i'm actually using a deductive method, all deductive of what i would do.If taking off the first one the problem is not solved, this could be indicating that the TRIAC that remains welded is the one of the problem, so you could take it off and replace it for the one you took off first...Think of the mas switches that should be open in normal conditions and should only closed when they have ther order from the microprocessor or microcontroller to make work what they have connected in their outputs...Obviusly if you have other replacement plates, you can use the same method and change it for one of those plates, no need tot take off the other one, if it is okay.If you didn't understand i can summarize it by ointing out the steps to be executed, without mixing it with the theory...Let me know!!!son semiconductores de TRES PATAS...en la foto puede verse que hay DOS patas soldadas y UNA que está en el medio más cortita, esa también cuenta...Es precisamente esa pata cortita la que corresponde al TERMINAL Nro. 2 y se conecta con el cuerpo del TRIAC que finalmente se apoya y suelda sobre la plaqueta...En resumen, visto como en la foto, de izquierda a derecha, el primer terminal soldado (de la izq) es el TERMINAL Nro.1, el segundo del medio (la pata cortita) es el terminal que se une con el cuerpo del triac por abajo y es el TERMINAL Nro2 y finalmente la pata de la derecha que está soldada es la COMPUERTA DE DISPARO....Si sospechás de un corto circuito, es probable que esté presente en el TERMINAL Nro. 1 y 2, asi que midiendo en esos 2 terminales podrías medir una baja resistencia...Aunque también puede estar en corto la COMPUERTA con alguno de ellos...Lo que se me ocurre que podrías hacer es: desoldar UNO de los TRIACS y enchufar la lavadora y verificar si el problema continúa o no...si se resuelve, quiere decir que sacaste el TRIAC en corto, y si continúa, entonces sacar el otro y volver a verificar...Uno de los 2 debería probocar el problema (hay un 50% y 50% de posibilidades)...Todo esto suponiendo que esos TRIACS hagan cosas diferentes, en realidad estoy usando un método deductivo de lo que Yo haría.Si sacando el primero no se resuelve el problema, esto podría estar indicando que el TRIAC que quedó soldado es el del problema, asi que podrías sacarlo y poner en su lugar el que sacaste primero...Pensalos como si se trataran de interruptores o switches que deberían estar abiertos en condiciones normales y que solo deberían cerrarse cuando tengan la orden del microprocesador o microcontrolador, de hacer funcionar lo que tengan conectado a sus salidas...Obviamente que si tenés otras placas de repuesto, podés usar el mismo método y cambiarlo por uno de esas placas, sin necesidad de sacar el otro, si estuviera bueno.Sino se entendió, lo puedo resumir puntializando los pasoa a ejecutar, sin mezclar teoría...Avisame !!!
luis38
luis38
95.432
hace 6 años
hace 6 años
Dear, you can use a triac from another plate type THT, instead of SMD. The BT137, it can work well. Greetings
Reparaciones similares solucionadas

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

4.93
(14)

Curso Reparación de Equipos de Audio de Alta Fidelidad

Maximiliano Resch
$ 60 USD
$ 20 USD
4.25
(8)

Reparación de Placa Main TV LED con el Ing. Picerno

Ing. Alberto H. Picerno
$ 40 USD
$ 20 USD
4.94
(16)

Curso Refrigeración Comercial Aplicado a Diagnóstico y Reparación

Ing. Georga Melgarejo
$ 40 USD
$ 13 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis