⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
T-5508

Very loud screaming bomb

Andres m2016
hace 5 años
hace 5 años
Good. I got this washing machine with a shriek (according to the owner came from trying it on the belt.) It made no noise at all. I put it in the drain and made the shriek that came from the drain pump. My problem is the next one to see if you can help me ... this bomb is old !! and I don't think I will get it. That's why I could get that sound. I also see that it brings wheelmen
electrico dj
hace 5 años
hace 5 años
Good I would say that you try to give it a good cleaning and see if you can get the last rudders if you do not get them you can reduce the noise a little by immersing them in naphtha until all the rust comes out and put a dry grease for rudders to dry out I hise it and I help a lot of greetings
juan guillermo caceres
hace 5 años
hace 5 años
Hello, that is a motor pump, earlier than what we know today as widespread. Very few houses are the ones that commercialize it and difficult to achieve, if the repair project does not have the expected results, you will have to start thinking about a pump adaptation with a nozzle included since the measures are different. Luck
Andres m2016
hace 5 años

Hi ... excuse me that I have closed the post ... the shriek comes from the engine ... not from the pump. I can immerse it in gasoline as "electriko" told me and then grease the rollers? The shaft looks rusty ..

Responder
juan guillermo caceres
hace 5 años

Friend, it is best to disassemble and change the rollers, it is not too much to "wash" the winding with naphtha and let it dry in the sun for a few hours, but if possible change the rollers. Regards

Responder
Andres m2016
hace 5 años

Yes ... my problem is that the head is under pressure ... and they told me that it can only be removed with a hydraulic press that I don't have ... is there another way to remove it?

Responder
juan guillermo caceres
hace 5 años

All right. The Achilles heel, right? If the motor pulley is made of aluminum, there is no big problem, now if it is made of iron, another is the issue and we proceed as you say.

Responder
Andres m2016
hace 5 años

This has already happened to me ... and I took it to a winding technician who charged me 800 pesos to change the 2 rulemsnes..all for not having the blessed press..if..the iron is the pulley ..

Responder
juan guillermo caceres
hace 5 años

As this issue of working with a press is somewhat difficult, the alternative would be to carefully remove the caps of the ruleman and wash it with gasoline, if you have to pass air under pressure and replace grease a little not much and reassemble. I clarify that this is only a temporary solution of medium duration
Regards

Responder
Andres m2016
hace 5 años

Hi Juan Guillermo ... if the pulley would be aluminum, how would I get it out?

Responder
juan guillermo caceres
hace 5 años

Hello, just give it a moderate heat for a few minutes, for example a cooking stove, the aluminum will soften and you can remove it with an extractor without major problems. Regards

Responder

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

4.25
(8)

Reparación de Placa Main TV LED con el Ing. Picerno

Ing. Alberto H. Picerno
$ 40 USD
$ 20 USD
4.6
(10)

Curso Localización de Fallas en Refrigeración en Heladeras/Neveras On/Off

Yamil Alarcón
$ 29 USD
$ 12 USD
4.71
(7)

Curso TV OLED y QLED con el Ing. Picerno

Ing. Alberto H. Picerno
$ 29 USD
$ 10 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis