⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
Electronics and Circuits

Extraction Yaxun 702

sadracst
hace 6 años
hace 6 años
in l The following photo has a red stripe marked all the affected air in my heat excerption and yaxun 702 and I want your help to know the names of those 7 marked components and thus be able to replace them to be able to regulate my extacion
Carlos Quiroga
hace 6 años

Hello, the black with six pins is an optocoupler which is below a resistance of 51 Ohm if it is (green-brown-black) or 510 if it is (green-brown-brown) the one that follows lower you have to pass the number as well as the one next to it since they can be transistors or regulators or triacs or scr the other resistance is 20 Ohm (red-black-black) the whites are connectors and the celestial can not appreciate if it is a relay or a capacitor would have You know the characteristics like being the numbers and letters that it brings.

Responder
sadracst
hace 6 años

thanks for your support
the resistance I buy is a 5.1 nose if it's the same

Responder
Carlos Quiroga
hace 6 años

No that value is smaller.

Responder
josduart
josduart
4.282
hace 6 años

It's 51 Ohms which in colors is green brown black

Responder
josduart
josduart
4.282
hace 6 años
hace 6 años
Here is the requested https://ibb.co/e8fTo0 if it is of your satisfaction do not forget to close the question with qualification ... BT136 Triac Relay Sy-24w-k L1523 MOC3023 R 51 Ohms
sadracst
hace 6 años

Thank you

Responder
josduart
josduart
4.282
hace 6 años

If it is the solution you expected you should accept it to close the question and not leave it open

Responder
VALERYRAMIREZ
hace 6 años

Good morning, does anyone have the schematic of this station, could they upload it?

Responder
Carlos Quiroga
hace 6 años

There must be a separate post with the order and the problem, those of others are not used.

Responder
HEVERT MAURICIO
hace 6 años
hace 6 años
B. Nights could help me, I have a problem with my BAKU 702 station. When plugging in, turn on the heat gun, before that I made a short and change Triac, the auto coupler, and still direct it turns on one by plugging in, in the back part some lines were soldered and I rebuilt it with cable but I am in doubt you can help me with a photo of the plate on both sides from now I thank you.
Carlos Quiroga
hace 6 años

Hi, you have to open a separate post with your specific problem.

Responder

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

4.93
(14)

Curso Reparación de Equipos de Audio de Alta Fidelidad

Maximiliano Resch
$ 60 USD
$ 20 USD
4.73
(22)

Curso Reparación de Fuentes Conmutadas de PC y Equipos Electrónicos

Maximiliano Resch
$ 40 USD
$ 20 USD
4.6
(10)

Curso Localización de Fallas en Refrigeración en Heladeras/Neveras On/Off

Yamil Alarcón
$ 29 USD
$ 12 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis