Hello forum, I am living in an area with very low electrical voltage so I bought an elevator, now I have a worse problem, the elevator has a high voltage and low voltage protection cut, it works between 240 and 140 volts so if there is less of that tension, it cuts it to me, well, it cuts it to me, and I want to know if that protection can be canceled because I prefer to unplug the refrigerator to run out of power. Thank you. I am not sure of the place of the consultation, if it is not here to move it please. Thanks again.

Hi. Did you buy an elevator or a voltage stabilizer? Canceling a protection is not recommended as loads will be burned. Cheers

Thank you for responding, it is an 8 kvw automatic lift that does not help me, I need to cancel the cut by low, what are the burns that burn?

Dannyben You do not indicate where you are from, but wanting to stabilize a voltage of 140V to 220V with 8KW load is impossible to achieve. If you have low voltage with the load you have, when you want to raise the voltage, you need more current consumption, which causes even more the voltage drop. The only explanation that I find to have such low voltage and not complaining to the distributor is when you have the authorized free service or you are illegally hanging on the power line. In case you do not know, these are the causes of the burning of transformers, since for what they were calculated, they far exceed the power with illegal hangers.

Thank you Ennio for your response, although I would like you to just answer what I asked without going into wandering places of residence or people illegally hanging from the power grid, and I clarify that with the elevator I have it would be very possible to raise the tension by canceling The low voltage protection cut.

[quote="Dannyben"] Thank you Ennio for your answer, although I would like you to just answer what I asked without going into wanderings about place of residence or people illegally hanging from the power grid, and I clarify that with the elevator I have it would be very possible to raise the voltage by canceling the low voltage protection cut. In case you do not know, my condition as moderator, it is my duty to ensure that illegalities are not promoted in the forum and less give recommendations that favor illegality.

Do not write to me in red and do not try to challenge me, I am not promoting any illegality, I just asked a question to try to solve a problem that I have, you should stop imagining things that are not, I recommend a vacation or get a woman, greetings. [/b]

If you were legally connected, with 10% less voltage that is 200V, the company has a duty to correct the low voltage by BAD ELECTRICAL SERVICE. Even report it to the regulator of electrical services.

If you feel like traveling, I invite you to my house so you can verify my connection with your own eyes, I live in La Plata, Argentina, let me know if you come to receive you as you deserve. Now please I ask you to stop intervening in the post so that if any other user has a solution you can offer it, thank you .

Closed topic

Closed topic

Is there a considerable distance between the energy intake and the point of consumption? what distance?

[size=120] Hi Julio Cesar, thanks for worrying, I tell you that the distance is that of a normal city house, the network cables pass through the sidewalk of my house and I live in front, between the network cable and The fuses are no more than 4 meters. That is not the problem, the problem is that the company does not send more than 180 volts and frequently reaches 130 although the moderator has a hard time believing it. [/Size]

A very low voltage, there is no regulator that can counteract such a large variation, which I mentioned about the protectors have always criticized it, I need a device that increases the voltage when it falls, I do not want a device that leaves me without electric power , to remove the clear low voltage protection that can be done, but I would prefer to increase the voltage instead, to eliminate the low voltage protection I do not know where and how to do it because I do not know what type of regulator it should be see the wiring diagram

Julio Cesar, it is impossible for me to increase the voltage, that depends on the company that provides the energy, all I can do is try to alleviate the situation, of course I am not going to pretend to increase from 130 to 220 but with raising it a little I am satisfied, I am tired of unplugging the eladera so that it does not burn.

It is not impossible to increase the voltage, if the maximum voltage that the electric company sends you is 180 volts, it is already missing about 50 volts, with an autotransformer it would achieve this voltage, here I have had neighbors with problems that the air conditioning does not turn on low voltage, I used an autotransformer, increasing 20 volts and with this solved the problem

[size=120] Well, we may be with a regional lexicon problem and what I have is an autotransformer that we know in Argentina as an elevator, my elevator / autotransformer perfectly raises the voltage as long as it does not drop below 140 v, and then cuts it as protection, what I want is to cancel that protection because when it goes down a lot they don't turn on the led lamps and I have to unplug the refrigerator and everything that has an engine, I want it to be kept at 160 or 170 when I go down to 130v, with that voltage already I'm used to living together. Thank you very much for the help. [/Size]

Indeed, removing the protection will take a voltage that will allow you to keep the devices on, to eliminate that protection you should already touch the internal circuitry of the device, what model and brand is it?

Hi Julio Cesar, the device says "Tornado 8 KW automatic tension booster" Of course you have to touch the internal circuitry, what I want to know is if you can. Thank you.

Thank you very much Julio Cesar, be very kind and helpful.