⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
Computers

Green LED of the motherboard turns on but the PC does not

JuaniSn
hace 6 años
hace 6 años
Hi, I have this problem with a cousin's computer. It turns out that my pc was damaged, we decided to test its source on my computer and verify that nothing else was damaged besides my power supply (which was what burned). Luckily my pc was serving normally, I just have to buy a new source. The problem now is that when we reassembled the power supply to my cousin's PC, it began to give problems. - At first it had turned on, then turned off and came back on again after 10min of being on. We left it off for a minute. - We turned it on again but this time it only lasted about 5 min on and did the same again. Of the scare we decided to leave it off so that it was not damaged or something. PS: When we turned it on, I remember that the PC emitted some beeps, I don't remember how many they were. There we opened the chassis to see what happened with the motherboard. If any cable interrupted or something, and then we turned it on again but this time it did not want to start anything. The green LED on the motherboard was still on but the PC did not want to boot. The source and the rams are discarded (because my cousin has already passed them an eraser). I think it could be a static problem, that we suddenly touched something without realizing it and it ended up damaging some component. What do you suggest I do? :( By the way, I have another separate question. [B] Can the processor be damaged if I dropped a screw on it? I have also thought that this affected its functioning somewhat. Thank you, I hope you can help me. [/B]
Piratacrimson
hace 6 años

Hello, remove the small battery that carries the motherboard for a minute and replace it, and if the motherboard has a built-in graphic, remove the graphic card if it has one, and connect it to the graphic on the board and tell us if you gave greetings image

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años
hace 6 años
Hello, it is almost certain that the movement has left something in false contact ... Check all the components that are perfectly clean ... and fit into their respective Slots .. Check the contacts that do not have rust .. If so clean them as well as the sockets, As for the screw, if the plate was not energized when falling, I do not vouch that it has damaged anything ... Regards
JuaniSn
hace 6 años

Hi. Everything is well connected, the components clean, the condensers were checked, the source was retested and the problem persists.
The sure problem is the motherboard. I was wrong with the question of the processor, the screw was that it fell on the south bridge, I confused it, excuse me. I begin to believe that the problem starts from there, something must go wrong with the south bridge because the rest is still good.
I have considered switching from motherboard to another similar model, but I don't know what it could be.
The board is an Intel destock board D865GSA.

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

The board of your choice must be compatible with your processor and memories. If you want to use these components ... When the problem is of that type, you can also make a budget in a specialized workshop. That case depends on your criteria. .. The screw, the same considerations fit ... Was the plate energized?

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

Seeing now (slow Internet) she is very old ,,, Consider changing the complete kit ... Since buying a used one of that age .. is half complicated ...

Responder
JuaniSn
hace 6 años

It was not energized, that was removing the screws from the source to test it. So I guess it was not the cause of the problem.
Yes, the model is very old. The processor is not the big deal either, the rams are 512mb and another 1gb. I would seek to buy a new board of a similar or slightly more advanced model to insert the same processor and rams, of course, that it is compatible. But as I emphasize, the processor does not reach intel i3, so a standard board I guess it could work.
I'm from Venezuela, we don't want to spend so much, just make it work

Responder
JuaniSn
hace 6 años

The processor is an intel pentium 4.

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

For the processor number ... or look for it here: http://www.cpu-world.com/index.html ... There you can get all the information to handle with the board ... Mercado Libre may be an option , but I don't know how it works in your country .. (I'm in Brazil)

Responder
JuaniSn
hace 6 años

I already researched, it's this: 506
https://articulo.mercadolibre.com.ve/MLV-518542795-processador-intel-pentium-4-506-266-ghz-lga-775-cache-1mb-_JM
Do you think an ASRock G41M-VS3 R2.0 board could use you? I've been reading about it and it seems that it can be compatible.

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

If you are sure that it is compatible with your processor? What is the model number of the ???

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

Another thing to see is the ram .. I presume yours is ddr400

Responder
JuaniSn
hace 6 años

The socket that both boards is LGA775, although that of the Asrock says: for Intel Core ™ 2 Extreme / Core ™ 2 Quad / Core ™ 2 Duo / Pentium® Dual Core / Celeron® Dual Core / Celeron processors
The processor that has this is a core. Would it influence something in a core and insert it into the Asrock? Just to get me doubt

Responder
JuaniSn
hace 6 años

The ram is that which you say, DDR400 DDR1, that if it is not compatible with the Asrock board that asks for DDR3 memories.

Responder
JuaniSn
hace 6 años

I believe that if the plate problem is not solved, it will be to buy a new one which is very expensive (at least here). I only have to take her to the technician to see what she says, although I imagine what the answer will be

Responder
JuaniSn
hace 6 años

I had come to think that when I was drawing the fountain and I dropped one of the screws on the south bridge, it would have damaged something. As all that is so delicate then.
This is weird. Is there anything else you can recommend, friend?

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

If the plate was not energized there is no problem with that .. Except of course that the object has been somewhat heavy. Pliers, screwdriver etc. I told you about the memories why watching the manuals. the ram are different on both boards, same with the same socket (https://www.intel.com/content/dam/support/us/en/documents/boardsandkits/desktop-boards/865/D865GSA/D865GSA_ProductGuide01.pdf) ( ftp://asrock.cn/Manual/G41M-VS3%20R2.0.pdf) With the single core processor, it will only limit you to a 32-bit System ....

Responder
JuaniSn
hace 6 años

Sep, the rams are different, but I think the processor can not be used ?. Thanks friend, if you can recommend something else, I will be super grateful.

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

The processor without problems .. But since you're going to spend on plates and also on Ram ... (I don't know if they do) Here sometimes they find plate / ram / proc kits. at quite affordable prices ... Verifying it is clear, the reputation of the seller if it is via ML I do not have how to recommend you from here, since the offers and availability will probably be different ....

Responder
JuaniSn
hace 6 años

These kits are also available here in the ML, although I have seen the prices of some low-end plates with ram and proc e the same is somewhat expensive but let's say something more "accessible" (they are like 10 minimum salaries).
Recommendations of some generic or low-end model of plates, if I do not find availability, at least I am guided by some similar models (I do not know much about this either). Thank you, I will put your answer as a solution for helping me in this haha.

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

And here one with better (Much better) Cost benefit https://produto.mercadolivre.com.br/MLB-1061274883-placa-me-asus-m4a78-processador-amd-x3-8gb-ddr2-_JM - it's all about of searching enough ...

Responder
Yonny Diaz
Yonny Diaz
2.185
hace 6 años

Although I must confess that I am a fan of AMD ... I currently have a Phenom X6 buldozer ... but I have been updating it since the time of the Atlhon 1.8 socket 462 XD Good evening ..

Responder
AMLVtecnico
hace 6 años
hace 6 años
Good afternoon, because of the requests that it emits, it may be that the RAM is not well placed or that it is dirty and that is why it does not detect it, it is probably turning off because it is heating some component of the main card.
JuaniSn
hace 6 años

Well, it doesn't turn on as I said, it only has the green LED on the card. We already clean the rams and all the other components are fine.
Something goes wrong on the motherboard.

Responder

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

4.93
(14)

Curso Reparación de Equipos de Audio de Alta Fidelidad

Maximiliano Resch
$ 60 USD
$ 20 USD
4.73
(22)

Curso Reparación de Fuentes Conmutadas de PC y Equipos Electrónicos

Maximiliano Resch
$ 40 USD
$ 20 USD
4.6
(10)

Curso Localización de Fallas en Refrigeración en Heladeras/Neveras On/Off

Yamil Alarcón
$ 29 USD
$ 12 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis