lg washing machine when turning on does not start and turn on the lights of the led blinking all of me can colavorar thank you very much
⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta.
🔥 Aprovechar oferta ahora 🔥
Clothes Washers and Dryers
lg washing machine when turning on does not start and turn on the lights of the led blinking all of me can colavorar thank you very much
lg washing machine does not start the led turn on
hace 6 años
hace 6 años
lg washing machine when turning on does not start and turn on the lights of the led blinking all of me can colavorar thank you very much
hace 6 años
Lg 13kg washing machine. Wf-5745spm partner that is similar to this one if you can help me thanks friend all the turbo led, wash, rinse and spin blink and no water comes out of the electrobalbula when turned on
hace 6 años
also when the prendo she moves a few seconds as if she were weighing the clothes for one side and the other, after a few seconds the LEDs begin to flash commented thanks please is urgent
27.259
hace 6 años
The urgency is set aside .--- The error code refers to spin failure .--- Remove the belt between the two pulleys and retest not before checking if the door switch lever is touching the tub of plastic .--- Involves removing the back cover to observe .--- Thanks and regards.
hace 6 años
friend is in the door a system like a fuse yo, I probe it in continuidada and does not give anything but e seen that they put a magnet to rehearse and verify that this good and not even
27.259
hace 6 años
Diego: Edit the initial contribution to incorporate a link where the box where the Reed Switch is placed on the Leds Card is illustrated .--- Here is the link on how to make the bridge: ----- http: // archivos.yoreparo.com/uploads/imagen_post/0001/11/8c1a0ea6358c7a4f27e0b63028c60b8264555149.png---- since I continue to confront problems to show the images of sketches related to the explanation provided. Check and comment then if the error persists .... Thanks and Regards.
27.259
hace 6 años
hace 6 años
If the door has a magnet on its underside, then it is not a fuse. It is the Reed Switch that is located on the card of the LEDs as illustrated in the following link to open with your browser through the copy and paste mechanism:
http://i.imgur.com/x3CsSGD.png
That error code would be related to the door error and only the wash and spin LEDs should be on. The magnet should be placed on top of the panel where the word Turbo is. However, open the door and locate the magnet you referenced at the bottom edge of the door and then, in a straight line, place a magnet on the panel and near that magnet to see if the Reed Switch manages to close its contacts. If that does not happen, you will be forced to remove the card and place the magnet directly on the Reed Switch to corroborate it.
Comment on this and apologize because I have had setbacks with an image that blocks me from sending the information I want to send. Thanks and regards.
-------------------------------------------------- EDITED ON 07-23-2017
Good afternoon Diego.
I leave you link to illustrate sketch where the Reed Switch is located. Try making a bridge between both ends of the windows where the Reed Switch is placed to see if the error disappears and allows the washing machine to work:
The link was placed in Comment because the problems with this topic continue.
If still making the bridge the error is still showing, you will have to contact an electronic or TV technician to check the circuit that feeds the Reed Switch in case of any damaged electronic component or if there are cold solders where it is inserted in the card.
Then comment on how it went. Thanks and regards.
----------------------------------------------- -Edited on 08-10-2017. [/B]
[b] Approach II:
** .- From: diego warrior-mouth .
Good afternoon friend btvictor but you were right I made a bridge but it was the same, I had to remove the card and take it to a technician and it was bad, they repaired it and I am good I also made a bridge in the switch and ready I am like new-.**
Observations:
Greetings diego.
Thank you for letting us know how the failure was finally resolved. May everything go well. Thanks and regards.
hace 6 años
hello friend but I put a magnet and nothing change is still the same I did as you tell me but nothing and I also put it directly and nothing
hace 6 años
Good afternoon friend btvictor but you were right I made a bridge but it was the same, I had to remove the card and take it to a technician and it was bad, they repaired it and I am good I also made a bridge in the switch and ready I am like new
Reparaciones similares solucionadas
¡Aprende a reparar con estos cursos YoReparo!
Curso Localización de Fallas en Refrigeración en Heladeras/Neveras On/Off
Yamil Alarcón
$ 29 USD
$ 12 USD
Curso Tecnología Inverter - Fabricación de probadores y herramientas
Yamil Alarcón
$ 240 USD
$ 40 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis
Ad