AN282

416

hace 5 años

this tv uses the independent source

manolo karvalo

30.814

hace 5 años

friend. I'm looking for the diagram to see what value the c531 is

manolo karvalo

30.814

hace 5 años

friend. with that chassis number I didn't find the diagram but in that the + b. It is 115volt. you might have raised the + b.

AN282

416

hace 5 años

ok I can connect myself and take the stress sample there in that capacitor to see how much is coming

AN282

416

hace 5 años

Friend the tv shows in the b + 135.7 and in the filter that inflates 8v I do not understand why it inflates according to the diagram that the friend passed the c531 is 22mfpor50v and I am placing it 47 by 100v I do not know if that is why it is inflated

manolo karvalo

30.814

hace 5 años

friend. it may be that you are placing it inverted polarity

AN282

416

hace 5 años

I'm placing it well friend

manolo karvalo

30.814

hace 5 años

friend. If the C531 is 22ufx50volt. and it can be inflated that some element that is related to that filter is short, check that stage well

AN282

416

hace 5 años

It will be fine that voltage of b + since the source comes out with that voltage now I don't know if the problem is at the source I have thrown that line and a diode arrives in that capacitor by the measurements is ok

manolo karvalo

30.814

hace 5 años

friend. there I indicate the colleague franciscovallarta ,. what you should do read down there

AN282

416

hace 5 años

I put a diode fr107 in place of the EL1Z and still it is still inflating it is watching in another post that the tv of independent source the b + is 135 so it would be good now what I do not understand why that condenser is inflated?

AN282

416

hace 5 años

The voltage in the capacitor is 8v as I said the only thing that the TV had checked before and when it arrived at the workshop I had a capacitor of 47 and according to this diagram is 22 by 50 I will check other elements to see if it agrees with this diagram

AN282

416

hace 5 años

The chassis number I located was this and matches that of the TCIA7S chassis source

AN282

416

hace 5 años

friend according to that dido is the EL1Z what would be its replacement?

franciscovallarta

22.858

hace 5 años

http://www.weisd.com/store2/NTE587.pdf

AN282

416

hace 5 años

friend I was checking the condenser that inflates according to diagram is the c541 of 22 percent and I am placing one of 47 it will be why it inflates because the diode apparently mind is well good I need the replacement because it sometimes measures well and ends up being the diode

AN282

416

hace 5 años

I put a diode fr107 and still it is still inflating estibe watching in another post that the tv of independent source the b + is 135 so it would be fine this now what I do not understand why that condenser is inflated?

AN282

416

hace 5 años

is in 135 friend right now so much check I got a resistance of 1/4 watt spoken according to the diagram are 0.47 ohms but I do not get it searched in chasi the one that I got was 4.7ohms and a new one of 6.8ohms I don't know if that is the cause of the condenser being inflated since I am placing it in the correct polarity

AN282

416

hace 5 años

I think I also have one of 0.120 0.22ohmn I would have to look for them

AN282

416

hace 5 años

friends I put uan thinking that it was 0.122 but without 1.2 according to the application the most sercano is 1ohns the one that is obtained from 0.47 is difficult to tell them to put that stop inflating the filter but I notice that it is scrin it is as with much birillo tried to lower it and the pamtalla is placed dark in its entirety and to see if I put the one on one to see if it improves a little beforehand many thanks to all for their collaboration in the resolution of the fault