⚡ Descuentos en cursos en video - Lleva tu aprendizaje técnico al siguiente nivel y aprovecha precios especiales antes de que termine la oferta. 🔥 Aprovechar oferta ahora 🔥
Monitors

My tv model SD-20z3 with black strip on the right side

ru35ruben
hace 5 años
hace 5 años
Hello friends, I want to know if you can help me with this problem tv series golden model SD20z3 with dark strip on the right side of the screen and according to the brightness of the image or channel something disappears a fault that also has is that if I regulate the flaybak screen to At least the image does not darken, it only remains opaque since I will appreciate the help
TobíasTv
TobíasTv
13.721
hace 5 años

my luck goes for what solutions

Responder
TobíasTv
TobíasTv
13.721
hace 5 años
hace 5 años
Hi Ru, change the capacitor that filters the 180 volts that go to the tube plate and solve, I greet Tobias
ru35ruben
hace 5 años

Hi friend, if you change all the 180v stage filters and horizontal stage counters too and the fault continues
The truth has me a little disoriented. If there is another alternative?

Responder
TobíasTv
TobíasTv
13.721
hace 5 años

take a picture of the fault

Responder
ru35ruben
hace 5 años
hace 5 años
TobíasTv
TobíasTv
13.721
hace 5 años

the image did not come out

Responder
ru35ruben
hace 5 años

Hello tobias if I do not know what happens that does not allow me to upload the image makes me invalid.
I apologize.

Responder
ru35ruben
hace 5 años

The problem persists in a black strip on the right side of the TV
Shadow type now on certain channels such as that fault decreases and in video mode the screen is half black and half gray with vertical stripes medium light green

Responder
TobíasTv
TobíasTv
13.721
hace 5 años

let's see, what tension do you have on the tube plate where it says 180 Volts

Responder
ru35ruben
hace 5 años

Hi tobias, I measure tension where you ask me I have 126v

Responder
ru35ruben
hace 5 años

What I am going to do is change the receiver if there is something changing but the diode marks me in good condition

Responder
TobíasTv
TobíasTv
13.721
hace 5 años

That is your problem, you have to have 180 volts, notice that it comes from the flyback, goes through a low-value resistor, filters it in a capacitor and goes to the transistors of the tube, for me it is the electrolytic one, you can put one of 10 micros by 250 volts or the resistance that is before the diode

Responder
ru35ruben
hace 5 años

If tobias this is how decis works with that voltage now I change the components and I tell you the result capo thousand thanks for the help

Responder
TobíasTv
TobíasTv
13.721
hace 5 años

there I left you an image

Responder
TobíasTv
TobíasTv
13.721
hace 5 años

notice if that is the diagram

Responder
ru35ruben
hace 5 años

Tobias told you that thanks to your guidance capo and solved the problem which was the resistance of low beacon of 1ohm which previously was measured and gave me ok.Now I replaced it to that resistance and the voltage raised to 190v which I seems a bit high

Responder
ru35ruben
hace 5 años

Thank you very much TobiasTV bonnet for the help and guide that persists in that stage of the 180v of the TV. By changing a r of 1ohm the image problem has been solved. Thanks bonnet.

Responder
TobíasTv
TobíasTv
13.721
hace 5 años

I'm glad, see you next time

Responder
Reparaciones similares solucionadas

¿Conoces una solución?

¡Aprende a reparar con estos cursos YoReparo!

4.93
(14)

Curso Reparación de Equipos de Audio de Alta Fidelidad

Maximiliano Resch
$ 60 USD
$ 20 USD
4.73
(22)

Curso Reparación de Fuentes Conmutadas de PC y Equipos Electrónicos

Maximiliano Resch
$ 40 USD
$ 20 USD
4.64
(11)

Curso Electrónica para Reparación de Placas

Santiago Cediel
$ 29 USD
$ 11 USD
¿Tienes una mejor respuesta a este tema? ¿Quieres hacerle una pregunta a nuestra comunidad y sus expertos?
Regístrate gratis